IPv6 address
How to get a public IPv6 address for your server, read its status and configure it manually if needed.
Each server can have one public IPv6 address. The address is direct, with no NAT: outbound connections use the server's own address, and inbound connections are opened only through port rules. IPv4 always stays, IPv6 is an addition and is free. It works on Linux and Windows servers.
Selecting it at order time
- In the order form, tick IPv6 address in the Access details section.
- The remaining steps are the same as a normal order.
The server gets the address at first boot; no separate reboot is needed. You see the address in Network → IPv6 addresses.
Activating on an existing server
- Open the Network page in the left menu and find the IPv6 addresses panel.
- Click Activate in the server row. The dialog shows the address and the gateway.
- Optionally tick Reboot now. If unchecked, the address is ready but the server does not pick it up until you reboot it.
- Click Activate.
On Linux the address is written to the server's cloud-init configuration and takes effect at the next boot. On Windows the address is written to the server configuration and the server adds it itself within a few minutes (netsh, persistent); no reboot is needed and the Reboot now box is not shown on Windows. The IPv4 address and settings never change.
Statuses
The portal reads the result from the QEMU agent on the server rather than only sending the request:
- Reboot pending: the address is in the configuration, the server has not rebooted yet.
- Applying on the server…: Windows: the server reads the address from its configuration and applies it itself (usually 2–5 minutes); on a new server this can wait until the initial setup finishes.
- Active: the agent saw the address on the server.
- Not confirmed: check on the server: the server rebooted, but the agent does not respond. The portal cannot verify the result.
- Not applied on the server: the server rebooted, the agent responds, the address is missing. On Linux cloud-init is probably disabled or the network is managed manually; on Windows the JezaHost IPv6 task on the server is not running or was removed. The Manual setup button appears in this case.
- Removal pending on server: the address was disabled; the server releases it when it reboots.
This feature requires cloud-init and the QEMU guest agent to be running on the server. If the agent was removed, the status never becomes "Active" and stays "Not confirmed".
Manual setup
The Manual setup button shows the address, prefix (/64), gateway and DNS and gives ready commands:
- Linux, immediately:
ip -6 addr addandip -6 route add default. - Linux, persistent: a netplan file for Ubuntu/Debian, an nmcli command for AlmaLinux.
- Windows:
netsh interface ipv6 add address,add route,add dnsservers.
Each command has a copy button. After configuring, the portal sees the address on the server within a few minutes and shows "Active".
Disabling
- In the IPv6 addresses panel, click Disable in the server row.
- Confirm with Disable in the dialog.
The address is removed from the configuration and the PTR and AAAA records are deleted. A Linux server releases it at its next reboot; Windows removes the address itself within a few minutes. Close the IPv6 gates in this server's port rules first, otherwise disabling is refused. If you added the address manually on the server, remove it yourself: the portal does not touch the inside of the server.
When a server is cancelled, its IPv6 address is released immediately, like a static IP: the PTR and AAAA records are deleted and the address returns to the pool. If you reinstate the service, activate the address again from the “Network” section; the same address is assigned.
PTR (reverse DNS)
The default PTR name works out of the box: host-<address with dashes>.ip6.jezacloud.com. To set your own name, click Change PTR in the row, enter the name and click Save. Only a name whose AAAA record points to this address is accepted. At most 5 changes per day.
Inbound connections
Ports are not opened automatically on IPv6. Turn on the IPv6 switch in the port rule row: the port opens on the server's IPv6 address with the same number, and the source restriction is shared with IPv4. Details: Port forwarding.
Limits
- On Windows, IPv6 is available only on servers created from the new Windows template; on older Windows servers the Activate button is not shown.
- One address per server. The address follows a formula and cannot be chosen.
- The additional /64 reserved for the server is not routed yet.
- Port 3389 (RDP) cannot be opened on IPv6.
- Outbound port 25 (SMTP) is blocked on IPv6 as well.